About: auto enthusiast YouTuber creating beneficial tutorial videos on both repairs and also customizations. Be certain to hit the SUBSCRIBE or follow button! an ext About 4DIYers »

Video indict on just how to loosen and also remove rusty bed bolts. Because that this truck, I should lift the box off in bespeak to change the cap corner, however you maybe merely removing the box, or girlfriend can additionally tilt package on the one side because that accessing a fuel pump instead of dropping a fuel tank or cutting a feet in the bottom of her box. Below I’m working through a 1998 Ford Ranger brief box which has a total of 6 bed bolts.

You are watching: How to remove a ford truck bed

Tools/Supplies Needed:

penetrating oil wire brush ratchet johnson bar torx chauffeurs brush


*
*
*
*
*

First start by for sure elevating the truck if girlfriend need much more room to gain access to the underside. For this i am utilizing drive ~ above ramps.

If you have actually a box liner like this truck, you’ll need to remove that. Remove any fasteners if it has actually any, open up the tail gate, and also then elevator it up from the center to retract the sides. As soon as there is sufficient movement because that the sides, retract the sides. You’ll most like need a helping hand to remove the box liner.


*
*
*
*
*
*

Now knowing precisely where those bed bolts are, you deserve to use the locations to identify where specifically they fasten to top top the frame. Unfortunately you can always have direct access to these bed bolts underneath. You should see bolts coming despite the frame which fastens come a clip. I’ve viewed these clips have actually a few different names, either a bolt clip, j clip, c clip, u nut, speed clip, or body clip.

Using a wire brush, clean up the exposed threads. These threads will certainly be going back through the threaded part of the clip, for this reason if they begin to bind, you deserve to either rest the clip or bolt. A hand brush works fine, but a power tool can also be offered too. Once satisfied, use a penetrating oil.

Moving ~ above the other exposed bolt, this truck together been oil sprayed at some point in it’s life so several of the metal is protected. Unfortunately in other areas it’s worn off due to being moved down gravel roads. Cleaning turn off the dirt, we have the right to see the threads are virtually like new. Penetrating oil will also be used just to it is in safe.

Unfortunately ns unable to get access to every the bolts as 2 are surprise behind the bumper frame work and also the other behind the fuel tank. If you space working close to the fuel tank, be mindful about sparks.


*
*
*
*
*
*
*
*
*
*

Using a hand brush is best. When this truck did have a box liner, the bolts are filled with some debris. Use a brush, pick, nail, or also wire brush to clean the end the top of the fasteners. If they’re not clean, we may not have an excellent contact with the torx bit, risking the possibility of stripping the head. If that happens, you’ll either need to cut, grind, or drill the bolt. Blow the end the debris and even insert the bit with may aid loosen debris too.

This truck provides T55 bits, you can use one impact, but not everyone has access to one and I nothing have affect torx bits, so ns using constant hand tools. A hand affect driver have the right to be used, I’ve shown this device in ahead videos. This I will be tackling v a johnson bar. The johnson bar enables for an ext leverage, friend not usage an expansion as this can twist her pivot point and danger stripping the head of the fastener. I do have a brief adapter here, 1/2” to 3/8” so i’m able to usage my 3/8” drive torx little -once the bolts have been broken free, occupational them ago and forth, loosening and also tightening them. This will minimize binding the the object and permit for the rust or dust to break up and also drop out.

You might need to go underneath and apply an ext penetrating oil if needed. I regulated to get all these bolts broken cost-free and up about a 1/4”. I will be leaving this over night, every bolt has penetrating oil applied from the height under the washer which should assist soak into the threads of the clips.


*

The next day ns then tightened up those bolts a pair threads to aid that oil work into the clips. Climate took mine time and also to loosen them, making use of the same procedure as previously if they’re binding and also finally lock are gotten rid of with no damaged bolts, clips, or damaged threads.

See more: Divinity 2 Red Ink In The Ledger, Red Ink In The Ledger


*
*

If you are elevating the box up ~ above the one side, I would certainly recommend placing hardwood blocks between the frame and box. The fuel filler neck may additionally need to be disconnected so you have actually the extra movement.

When reinstalling the bolts, a dye seed is recommended to clean increase those threads therefore installation is make easy.

Do you have tips on how to eliminate sap? please be sure to share that in the comments below. Stay up to day with my latest tutorials, don"t forget to monitor my profile and be certain to check out my YOUTUBE page as well for all her DIY needs. Likewise be sure to follow my various other social media pages such together Facebook, Instagram, Pinterest, Google Plus, and also Twitter.